PROFINET Device to Modbus Serial
inkl. mva.
PROFINET Device to Modbus RTU/ASCII Master/Slave Gateway
The PROFINET device to Modbus Serial gateway offers bi-directional data transfers between a PROFINET Controller and Modbus serial (RTU and ASCII) devices. The serial port can be configured as either a Modbus master or slave. The PROFINET interface operates as a PROFINET device (slave).
The PLX31-PND-MBS gateway is a stand-alone DIN-rail mounted unit that provides Ethernet connectivity for network communications, remote configuration, and diagnostics. The onboard SD Card slot (SD card optional) is used for storing configuration files that can be used for recovery, transferring the configuration to another gateway, or general configuration backup.
Features and Benefits
- PROFINET v2 certification with PROFINET class A compliance
- Field-proven with thousands of Modbus serial devices, and multiple PROFINET controllers from multiple vendors
- Remotely view and diagnose Modbus and PROFINET networks
- Remote configuration via the free, intuitive, ProSoft Configuration Builder (PCB) software
- The Modbus serial port supports master or slave mode
- Secure module configuration via module switch (v1.04 and greater)
- Up to 10,000 16-bit registers can be used to exchange large amounts of data.
Technical Specifications
|
PROFINET Specifications |
|||
| Specification | Description | ||
| Driver Type | Class A Device | ||
| PROFINET I/O Data | 1440 bytes IN, 1440 bytes OUT | ||
| Exchange Types | Cyclic Real-time (RT) and Acyclic Data | ||
|
Modbus Serial Specifications |
|
||
| Command List | Up to 100 commands, each fully configurable for Function Code, slave address, register to/from addressing and word/bit count. | ||
| Supported Modbus Function Codes | 1: Read Coil Status | 15: Force (Write) Multiple Coils | |
| 2: Read Input Status | 16: Preset (Write) Multiple Holding Registers | ||
| 3: Read Holding Registers | 22: Mask Write Holding Register (slave only) | ||
| 4: Read Input Registers | 23: Read/Write Holding Registers (slave only) | ||
| 5: Force (Write) Single Coil | |||
| 6: Preset (Write) Single Holding Register | |||
| Software configurable communication parameters | Baud rate: 110 baud to 115.2 kbps | ||
| Parity: None, Even, Odd | |||
| Data Size: 7 or 8 bits | |||
| Stop bits: 1 or 2 | |||
| RTS on/off delay: 0 to 65535 milliseconds | |||
| Modbus Modes: RTU with CRC-16, ASCII mode with LRC error checking | |||
| Floating Point Data supported, support for Enron and Daniel | |||
| Polling of Command List | Configurable polling of command list, including continuous and on change of data | ||
| Status Data | Error codes available on an individual command basis. In addition, a slave status list is maintained | ||
| Node Address | 1 to 247 (software selectable) | ||
| RS Interface | RS232, RS422, and RS485 | ||
| Hardware Specifications | |
| Specification | Description |
| Power Supply | 24 VDC nominal |
| 10 to 36 VDC allowed | |
| Positive, Negative, GND Terminals | |
| Current Load | 24 VDC nominal @ 300 mA |
| 10 to 36 VDC @ 610 mA maximum | |
| Operating Temperature | -25°C to 70°C (-13°F to 158°F ) |
| Storage Temperature | -40°C to 80°C (-40°F to 176°F ) |
| Relative Humidity | 5% to 95% RH with no condensation |
| Shock | IEC 60068-2-27; 15G @ 11ms, 3-Axis (Operational) |
| IEC 60068-2-27; 30G @ 18ms, 3-Axis (Non-Operational) | |
| Vibration | IEC 60068-2-6; 5G @ 10 to 150 Hz |
| Dimensions | 5.38 x 1.99 x 4.38 in, 13.67 x 5.05 x 11.13 cm (H x W x D) |
| LED Indicators | For configuration and protocol status errors |
| Ethernet Port | *10/100Mbit RJ45 Connector Electrical Isolation 1500 Vrms at 50 Hz to 60 Hz for 60 seconds, applied as specified in section 5.3.2 of IEC 60950: 1991 |
| *Ethernet Broadcast Storm Resiliency - less than or equal to 5000 [ARP] frames-per-second and less than or equal to 5 minutes duration | |
| Number of Serial Ports | 1 |
| Shipped With Each Unit | 2.5 mm screwdriver, J180 Power Connector, DB9 to Screw Terminal Adapter |