Anybus Wireless Bolt Serial 18-pin white
incl. VAT
Anybus Wireless Bolt Serial 18-pin converts serial RS232/RS485 data to TCP/IP communication over the wireless link. It also works as a router for Modbus-TCP to Modbus-RTU enabling transparent access to all your existing serial Modbus devices.
Anybus Wireless Bolt Serial enables you to connect industrial machines and devices to a wireless network. It is attached onto a cabinet or a machine to enable wireless access over Bluetooth®, or WiFi (Wireless LAN). It converts serial RS232/RS485 data to TCP/IP communication over the wireless link. It also works as a router for Modbus-TCP to Modbus-RTU enabling transparent access to all your existing serial Modbus devices.
With Anybus Wireless Bolt you get an All-in-one package featuring, connector, communication processor and integrated antenna in the same unit, with an industrial IP66/IP67 protection class.
FEATURES & BENEFITS
- Serial RS232/RS485 to wireless and TCP/IP conversion
- Communication over WiFi or Bluetooth
- Serial cable replacement “serial to wireless to serial”
- Wide baudrate support 2400 to 921600 Bit/s
- Special Modbus-RTU mode
- Modbus-TCP to Modbus-RTU routing
- Web-configuration over wireless or ethernet
- Available with white top Sunbolt enabling 30% higher surrounding temperature compared to black in direct sunlight
- Full compatibility with Anybus Wireless Bridge and Anybus Wireless Bolt Ethernet
- CLI (Command Line Interface) for configuration and diagnostics
Product support and documentation
Key Use Cases
Cable Replacement
Common bus
Multi-point; Serial to Bolt to WLAN/BT to many Bolt to Serial Up to 8 participants (1 master and 7 slaves). Wireless multi-drop (master–slave). The Bolt is transparent. Message from host to Bolt is forwarded to all slaves. Every slave response forwarded to the host. Suitable for master/slave polled protocols with RS485, e.g. Modbus RTU.
Modbus-TCP to Modbus-RTU router/gateway
Converting serial RS232/RS485 data to TCP/IP over wireless and wired
TCP/IP Socket to RS232/RS485
WLAN/BT to one or several "Bolt Serial" to serial devices. Raw data to TCP port. Any serial protocol.
Technical Specifications
| Serial interface |
Serial: RS232/RS485 Baud rate: 2400 - 921600 bit/s |
| Ethernet interface |
Ethernet: 10/100BASE-T with automatic MDI/MDIX auto cross-over detection. For configuration only. |
| WiFi interface |
Wireless standards: IEEE 802.11 a, b, g, n, d. |
| Bluetooth interface |
Wireless standards (profiles): PANU, NAP & SPP |
| Dimensions |
Diameter: 68 mm. Height: 75 mm (95 mm including connector. Outside height: 41 mm) |
| Weight |
81g |
| Temperature Bolt (black) |
Shadow: -40 to +65 °C |
| Temperature Sunbolt (white) | Shadow and direct sunlight: -40 to +65 °C Storage temperature: -40 to +85 °C |
| Output Power | WiFi 18 dBm EIRP - Bluetooth 14 dBm EIRP - Bluetooth Low Energy 10 dBm EIRP All including antenna gain 3dBi |
| Power Supply | 9-30 VDC (-5% +20%), Cranking 12V (ISO 7637-2:2011 pulse 4). Reverse polarity protection. |
| Power Consumption | 0.7W idle, 1.7W max (54mA@24VDC with Wireless LAN and 36mA@24VDC with Bluetooth) |
| Enclosure material | Top: Valox 357X(f1) PBT/PC. Suitable for outdoor use with respect to exposure to ultraviolet light, water exposure and immersion in accordance with UL 476C. Bottom: Celanex: XFR 6840 GF15. PBT glass reinforced plastic. |
| Mechanical rating | IP66 and IP67 for top (outside the host), IP21 for bottom (inside the host), UL NEMA 4X |
| Mounting | M50 screw and nut (50.5 mm hole needed) |
| Antenna | One built in antenna |
| Connector | Included plug connector (2x9p; 3.5mm, Phoenix DFMC 1.5/9-ST-3.5, push-in spring connection) |
| Vibration Compatibility | Sinosodial vibration test according to IEC 60068-2-6:2007 and with extra severities; Number of axes: 3 mutually perpendicular (X:Y:Z), Duration: 10 sweep cycles in each axes, Velocity: 1 oct/min, Mode: in operation, Frequency: 5-500 Hz, Displacement ±3.5 mm, Acceleration: 2g. Shock test according to IEC 60068-2-27:2008 and with extra severities; Wave shape: half sine, Number of shocks: ±3 in each axes, Mode: In operation, Axes ± X,Y,Z, Acceleration: 30 m/s2 , Duration: 11 ms. |
| Certifications |
|
| Europe | ATEX: ATEX Category 3, zone 2 according to EN60079-15, product marking: EX II 3 G nA IIC T4. CE, 2014/53/EU Radio Equipment Directive (RED) |
| USA | FCC 47 CFR part 15, subpart B. UL: Ind. Cont. Eq. also Listed Ind. Cont. Eq. for Haz. Loc. CL1, DIV 2, GP A,B,C,D, T4. UL file: E203225 |
| Canada | ICES-003 |
| Japan | MIC |
| Other countries | Brazil, Australia, Colombia, Turkey, Malaysia, Argentina, India, Chile, Korea |
